Leapers Oprmr20Cts Op3 Micro Sls Single Dot Black Anodized 1X 4 Moa Red Reticle
$129.97
$139.97
Leapers
Leapers Oprmr20R Op3 Micro Single Dot Black Anodized 1X 4 Moa Red Reticle
$119.97
$129.97
(You save
$10.00
)
The Leapers Oprmr20R Op3 Micro red dot sight brings compact, reflex optics to pistol platforms without the bulk or complexity. Built for shooters who want a fast, reliable aiming solution on optics-ready handguns, this single-dot red dot sight delivers a clean 4 MOA red reticle in a low-profile package that plays well with your existing setup. The black anodized housing is tough enough for duty and range work, and the removable mounting base makes it easy to swap between guns or store it safely.
What sets this sight apart is thoughtful engineering for real-world carry and duty use. The optic height is designed to co-witness with most suppressor-height iron sights, so you're never left without a backup aiming point if the battery dies or the optic fails. A laser-engraved tertiary aiming point on the rear hood adds another layer of redundancy—a feature you'll appreciate in low-light or emergency situations. It accepts the common RMR footprint, meaning it's compatible with most modern optics-ready pistol systems and mounting plates already in circulation.
Installation is straightforward if you follow Leapers' torque specs: use only the included #6-32 or #4-40 screws (don't improvise), tightened to roughly 12 inch-lbs for the optic itself and 35 inch-lbs for the side plate. A protective optic cover ships with the sight to keep the lens clean in your range bag or holster.
Key Features
- RMR-footprint mounting base—compatible with most optics-ready pistol slides
- 4 MOA red dot reticle for quick target acquisition at typical defensive ranges
- Co-witnesses with suppressor-height iron sights for reliable backup aiming
- Laser-engraved tertiary aiming point on rear optic hood
- Low-profile, removable mounting base for easy swaps between platforms
- Protective optic cover included
- Black anodized finish resists corrosion and wear
Specifications
| Brand | Leapers | |
| Model | Oprmr20R Op3 Micro | |
| Reticle Type | Single red dot | |
| Reticle Size | 4 MOA | |
| Magnification | 1X | |
| Mounting Footprint | RMR | |
| Finish | Black anodized | |
| Included Accessories | Removable low-profile Picatinny mounting base, protective optic cover | |
| Mounting Hardware | #6-32 or #4-40 screws (included) | |
| Recommended Torque (Optic) | ~12 inch-lbs | |
| Recommended Torque (Side Plate) | ~35 inch-lbs |
Frequently Asked Questions
Is this red dot compatible with my optics-ready pistol?
If your pistol uses an RMR-pattern mounting footprint, yes. The Leapers Oprmr20R Op3 uses the common RMR interface, which is standard on most modern optics-ready handguns. Always verify your specific slide's footprint before purchasing.
Will it work with my iron sights?
The optic height is designed to co-witness with most suppressor-height iron sights, so you can use your backup irons if needed. Additionally, there's a laser-engraved tertiary aiming point on the rear hood of the optic as a failsafe.
What's the correct way to install this sight?
Use only the included #6-32 or #4-40 screws—do not use other fasteners. Tighten the screws mounting the optic to approximately 12 inch-lbs, and the side plate screw to approximately 35 inch-lbs. Leapers provides these torque specs to prevent over- or under-tightening.
What comes in the box?
The sight includes a removable low-profile Picatinny mounting base, the necessary mounting hardware (#6-32 and #4-40 screws), and a protective optic cover to keep the lens clean when not in use.
